Food Science and Preservation
The Korean Society of Food Preservation
Research Article

Effect of extracting solvents on physicochemical properties of vegetable seed oils and their suitability for industrial applications

Qeency Etim Essien1https://orcid.org/0009-0008-9046-658X, Michael Akomaye Akpe2,*https://orcid.org/0000-0001-7258-7427, Ofonime Okon Udo2https://orcid.org/0009-0005-9685-1671, Collins Irechukwu Nwobodo2https://orcid.org/0009-0000-0418-719X
1College of Nursing Sciences, Calabar 540242, Nigeria
2Department of Pure and Applied Chemistry, University of Calabar, Calabar 540242, Nigeria
*Corresponding author Michael Akomaye Akpe, Tel: +234-90469092, E-mail: michael.akpe@unical.edu.ng

Citation: Essien QE, Akpe MA, Udo OO, Nwobodo CI. Effect of extracting solvents on physicochemical properties of vegetable seed oils and their suitability for industrial applications. Food Sci. Preserv., 31(4), 554-564 (2024)

Copyright © The Korean Society of Food Preservation. This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

Received: Oct 10, 2023; Revised: Aug 11, 2024; Accepted: Aug 12, 2024

Published Online: Aug 31, 2024

Abstract

The effects of extracting solvents on the physicochemical properties of vegetable oils extracted from four oil seed plants, namely Dennettia tripetala, Dacryodes edulis, Cola rostrata, and Persea americana, were studied. Vegetable oils were extracted using the Soxhlet method. The oils were used for determining % yield, acid value (AV), iodine value (IV), saponification value (SV), electrical conductivity (EC), and pH. The results revealed that the range of the mean % yield of oils extracted using hexane, carbon tetrachloride (CCl4), petroleum ether, acetone, and methanol, respectively, were 7.5-12.0, 9.0-22.0, 7.5-27.5 and 12.0-37.5 for the four oil Seeds respectively. Mean AVs of oils in mg KOH/g across the solvents were 3.1-3.7, 3.1-3.8, 2.5-3.9 and 2.4-2.8 for Cola rostrata, Dacryodes edulis, Dennettia tripetala and Persea americana respectively. Mean IVs of oils in gI2/100 g across the solvents were 33.25-33.97, 33.06-33.35, 32.06-33.76 and 33.00-34.00 for the four oil seeds, respectively. Mean SVs in mg KOH/g across the solvents were 191.00-197.44, 190.74-198.31, 194.11-202.52, and 182.23-199.44, respectively. Mean EC values ranged 0.31-0.32, 0.30-0.33, 0.30-0.33, and 0.31-0.32 μS/cm across the solvents, respectively. Mean pH values ranged from 6.1-6.4, 4.6-6.3, 6.2-6.4, and 6.1-6.3 across the solvents for the oils, respectively. The AVs of the oils suggest that they are edible oils, the IVs classify the oils as non-drying oils suitable for paint making, and SVs reveal that the oils are good for soap making. Hexane, petroleum ether, and CCl4 are suitable for oil extraction industrially, while D. edulis, D. tripetala, and P. Americana oils are economically viable oil resources due to their high percentage yield, SV and IV.

Keywords: vegetable oils; extracting solvents; physicochemical properties of oils; palm kernel oil

1. Introduction

Fruit seeds are the by-product of fruit processing into juice and other products. Despite being treated as waste, fruit seeds contain oil with health benefits comparable or even higher than the conventional seed oil from field crops (Kaseke et al., 2020). Seed oils are crude fats extracted from plant seeds, and they are important ingredients in many foods, medicine, cosmetics, fuel (Biodiesel), etc. (Vermaak et al., 2011). Nigeria is blessed with many oil seeds which are good supplements in food, oil paints, cosmetics, and other industrial purposes (Onyeike and Acheru, 2002). Examples of such seeds include soybean seed oil, tiger nut oil, peanut oil, palm oil, palm kernel oil, etc. Their yields, composition, and types of extraction solvents used determine their usefulness in various applications (Aluyor and Ori-Jesu, 2008). According to Roy et al. (2022), vegetable seeds that often constitute a hefty share in food waste generation, can be valorized as a food fortification and/or preservation agent. That is, vegetable seeds often discarded as waste can be processed and converted into valuable substances. Fruit seeds are leftovers from a variety of culinary sectors. These seeds not only possess various nutritional attributes but also have many health-beneficial properties. One way to make use of these seeds is to extract their bioactive components and create fortified food items (Roy et al., 2024). One of the nutritional attributes and or bioactive components of seeds that can be extracted is oil or fatty acids.

Extraction of seed oils can be done through many methods such as ultrasonic-assisted extraction, microwave-assisted extraction, mechanical extraction, supercritical fluid extraction, aqueous enzymatic oil extraction, and also Soxhlet extraction (Felix and Clement, 2011). Soxhlet extraction method helps to recover a component from either a solid or liquid, and it is straightforward and inexpensive (Luque-Garcia and Luque de castro, 2004). Extracting solvents are liquids used to remove or separate some components from a substance during the extraction process. Examples are methanol, hexane, acetone, carbon tetrachloride, diethyl ether, petroleum ether, ethanol, etc. This research focuses on the extraction of Dennettia tripetala seed, Dacryodes edulis seed, Cola rostrata seed and Persea americana seed through the Soxhlet extraction method using methanol, hexane, acetone, carbon tetrachloride, and petroleum ether as solvents.

Cola rostata, commonly called monkey cola in Nigeria and “Ndiya” in Southern Nigeria, belongs to the genus Cola, which is the largest genus of the sterculiaceae family of flowering plants. Cola rostrata, commonly known as monkey cola, is from the k. schum species, a member of malvaceae family, malvales order, and also from the genus of Cola. Cola rostrata fruits are edible and have a sweet taste, the seed is reddish brown in color, and the fruit and seed of C. rostrata have not been reported to be used in folk medicine (Emmanuel et al., 2013). Cola gigantean leaves, as reported by Idu et al. (2010), help to improve the supply of blood in the body.

Dacryodes edulis known commonly as African pear, is always available for about six months in a year (Eka, 1997). D. edulis commonly called African or native pear is of the D. edulis species, spindales order, burseraceae family, and a genus of Dacryodes. Some animals feed on the seeds of native pears, while humans eat them when raw, roasted, or boiled in hot water (Kadji et al., 2016). African pear can be used as an alternative source of fats and oil for both domestic and industrial use. The oil of African pear contains linoleic acid, which is a vital polyunsaturated fatty acid that helps in the prevention of vascular heart diseases (Ajiwe et al., 1997), and it also has a greater amount of oxidative stability.

Dennettia tripetala, known as pepper fruit, belongs to the magnoliate order; it’s a member of the annonaceace family; it is uvaropsis genus and uvariopsis tripetala species. D. tripetala, commonly called pepper fruit, is cultivated throughout the tropical rainforest region of West Africa. It is red when ripped and green when unripe and has a spicy, pungent taste; the pepper fruit plant flowers at the beginning of the rainy season, especially during the months of April and May (Umoh, 1998). It is used traditionally for the entertainment of guests in Igbo land, Nigeria. Oyemitan et al. (2008) reported that the essential oil from D. tripetala contains anti-inflammatory and analgesic properties, as a result of this, the essential oil can be used for reducing body inflammation and pain.

Persea. Americana, commonly known as avocado, is a member of the Lauraceae family; it’s of the Lauralis order, persea genus, and P. americana species. P. americana (Avocado) is among the plants contributing to health improvement due to the presence of bioactive chemicals that are essential to health (Okwu, 2001; Okwu and Morah, 2004). The biological effects of avocado seed extracts include its use as an anti-cancer agent (Abubakar et al., 2017).

The seeds of D. edulis (African pear) were also studied and reported by Obasi and Okolie (1993) to contain 76 kg−1 of carbohydrates, 126 kg−1 of lipids, and a high crude fiber of 273 kg−1. Arisa and Lazarus (2008) investigated the possibility of producing good quality oil from the seeds of D. edulis (African pear) and reported the oil content of the native pear seed to be 50%, with an acid value of 9.6 mg KOH/g, saponification value of 172.8 mg KOH/g and iodine value of 33 mL/g. Thus the oil produced can be classified as a non-drying oil because of its range of iodine value.

According to Shirana et al. (2011), the soxhlet extraction of Jatropha curcas L. seed oil gave a maximum yield of 75% with hexane when compared with other solvents, Isopropanol yielded 59% of the seed oil while petroleum ether gave 53% yield. In search for alternative solvents for Moringa oleifera seeds extraction among hexane, isopropyl alcohol, and petroleum ether within a time range, the highest oil yield was obtained with petroleum ether followed by hexane before isopropyl alcohol (Efeobokhan et al., 2015). There is also a report in which isopropyl alcohol yielded 94.7% while petroleum ether gave a yield of 72% in the extraction of coconut seed oil (Okene and Evbuomwan, 2014).

Despite the use of some of these seed oils extracted using different methods or some solvents domestically, there is at present little or no information or reports on the comparative effect of extracting solvents on the seed oils properties and the suitability of extracting solvents for a specific oil property and a particular industrial use over a wide range of different extracting solvents. The objective of this study is to determine the percentage yield and physicochemical properties of C. rostrata, D. edulis, D. tripetala, and P. americana seed oils extracted using five different solvents and determine their suitability for domestic or industrial use. Also, to compare their properties with palm kernel oil (PKO) that is usually used industrially and analyze the effect of extracting solvents on the oil properties and the suitability of a particular extracting solvent for a particular property and industrial use. This will provide a guide to solvent selection for seed oil extraction for a specific purpose.

2. Materials and methods

2.1. Sample collection

Fresh, ripped, and matured fruits of Cola rostrata, Dennettia tripetala, Dacryodes edulis, and Persea americana were obtained from Akim- Akim in Odukpani Local Government Area of Cross River State and were identified at the Herbarium Centre of Botany Department, University of Calabar, Nigeria.

2.2. Sample preparation

The fruit samples were taken to the laboratory of the Department of Pure and Applied Chemistry, University of Calabar, Nigeria, where they were peeled to get the seeds. The fresh seeds were washed with distilled water, sliced where applicable, and dried in an oven at 60°C for 2 days (gradual drying) before being ground into powder. The powdered form of each sample was used for the extraction of oil (Akpe and Inezi, 2018).

This was done according to the procedures of (AOAC, 1998) where 100 g of each powdered dry seed sample was weighed, wrapped with filter paper and transferred into the thimble of the Soxhlet extractor fitted on a 250 mL round bottom flask containing 120 mL of the solvent (either hexane, petroleum ether, CCl4, acetone or methanol, all produced from British Drug House, Poole, England) and anti-bombing granules. The flask was connected to a reflux condenser and placed on an electric heater at a temperature of 40-60°C to reflux for 5 hours. After this period, the thimble was removed from the Soxhlet with the defatted sample, and the solvent was evaporated off the flask using a water bath at 30°C. The lipid extract in the flask was then cooled in a desiccator, weighed, and labeled.

2.3. Percentage yield

The percentage yield of each of the solvents used was measured as its extraction efficiency, which is the ratio between the actual or experimental value and the theoretical value. The actual yield is the amount of product actually obtained from the chemical reaction or experiment carried out. The theoretical yield (predicted yield) is the amount of product that could possibly be produced in a given reaction, calculated according to the starting amount of the limiting reagents.

Percent yield  =  Experimental value   Theoretical value  × 100
(1)

Where, Experimental value = oil weight; Theoretical value = sample weight.

2.4. Physicochemical analysis

The physicochemical analysis deals with both the physical and chemical properties of the oil. The physical properties analyzed in the course of this research work were temperature, pH, and conductivity, while the chemical properties analyzed were the acid value, iodine value, and saponification value.

2.4.1. Acid value (AV)

Five grams (5 g) of oil extract was weighed accurately into labeled conical flasks, 50 mL of 95% ethanol was boiled in a second flask, and while still above 70°C, it was neutralized with 0.1 M KOH using phenolphthalein indicator (2 drops). The neutralized ethanol was poured into the flask containing the oil extract, and the contents of the flask were mixed while still hot. The mixture was titrated with 0.1 M KOH with vigorous shaking during the titration. The endpoint of the titration was detected when the addition of a single drop of phenolphthalein produced a slight but definite color change which persisted for about 20 sec (AOAC, 2002).

Acid value  = 56.1 × V × N W
(2)

Where

W: The weight of the oil extract sample in grams

V: Volume in mL of potassium hydroxide

N: Normality of potassium hydroxide

2.4.2. Iodine value (IV)

One gram (1 g) of the oil extract was accurately weighed and dissolved with 10 mL of CHCl3 in a glass stoppered flask, 25 mL of Hanus’ iodine solution was added with the help of a pipette filled by suction with a rubber bulb. The blank determination was conducted in all respects, similar to that of the sample. The mixture was well mixed by swirling and was allowed to stand at room temperature for 30 minutes in a dark cabinet with occasional swirling. After 30 minutes, the mixture was removed from the dark cabinet and 10 ml of 15% KI solution was added, 50 mL of water was added to the mixture. The mixture was titrated with standard 0.1 N sodium thiosulphate solution using 50 mL burette until the yellow color of the solution was almost colorless; at this point, 2 mL of starch solution was added, which turned the solution to a deep blue color. The completion of the reaction was indicated by the disappearance of the blue starch iodine color, mixing well during the final stages of titration.

Iodine value  = ( X Y ) × N × 12.69 W
(3)

Where

X: Volume in mL of sodium thiosulphate solution required for blank titration

Y: Volume in mL of sodium thiosulpate solution required for sample

N: Normality of the sodium thiosulphate solution

W: Weight of sample

12.69: Miliequivalent weight of Iodine

2.4.3. Saponification value (SV)

One gram (1 g) of the oil extract was weighed and put into a 250 mL round bottom flask. Twenty-five mL of methanolic KOH was added to the flask content. The flask was then connected to a reflux condenser and refluxed in a water bath for one hour, care was taken to ensure adequate and complete saponification by swirling the contents of the flask at frequent intervals. The flask was removed from the boiling water after one hour. To each flask, 3 drops of phenolphthalein indicator were added, and the content was titrated against standard 0.5 M hydrochloric acid when it was still hot. A blank titration was carried out with the same quantity of methanolic KOH solution under the same conditions (AOCS, 1993).

Calculation:

Saponification value  = 56.1 × M × ( Y Z ) W
(4)

Where

M: Molarity of HCl in Mol/dm3

Y: Volume of HCl required for blank titration in mL

Z: Volume of HCl required for real titration in mL

W: Weight of oil extract sample taken in grams

2.4.4. Determination of electrical conductivity

The conductivity meter (4510 JENWAY, Bibby Sci. Ltd., Dunmow, England) was used, and the probe was dipped into the sample after rinsing with distilled water. The value was read and recorded.

2.4.5. pH determination

The pH meter (pH meter SD20, Mettler-Toledo, India.) was used for the determination; the pH meter probe was dipped into the sample, and the value was recorded after stabilization.

2.5. Statistical analysis

Five replications of the experiment were carried out for each measured value, and the data was reported as the mean ±standard deviation (SD) (n=5), in the Table of results. IBM SPSS Version 20 software was used to carry out one-way ANOVA and significant tests (Duncan’s new multiple range test) on the data obtained from the experimental procedure at p<0.05. The significance indication was also stated using superscript letters of alphabets in the Tables.

3. Results and discussion

The results of the physicochemical analysis of Cola rostrata, Dacryodes edulis, Dennettia tripetala, and Persea americana seed oils are shown in Tables 1-5.

3.1. Percentage yield

The results of the percentage yield of the seed oils of C. rostrata, D. edulis, D. tripetala, and P. americana extracted with acetone, carbon tetrachloride, hexane, methanol, and petroleum ether are shown in Table 1.

Table 1. Percentage (%) yield of oil extracts using different solvents
Sample Hexane CCl4 Petroleum ether Acetone Methanol
Control1) 27.00±0.202)b3) 23.50±0.10a 26.00±0.20b 23.00±0.10a 24.00±0.20a
Cola rostrata 7.50±0.10a 7.50±0.10a 8.00±0.20a 9.00±0.10b 12.00±0.20c
Dacryodes edulis 22.00±0.20c 9.00±0.20a 22.00±0.10c 20.00±0.20b 11.00±0.20a
Dennettia tripetala 17.00±0.20b 7.50±0.10a 16.00±0.10b 16.00±0.20b 27.50±0.20c
Persea americana 27.50±0.20d 12.00±0.20a 21.00±0.10c 16.80±0.10b 27.00±0.10d

Commercial palm kernel oil (PKO).

Values are mean±SD (n=5).

Different superscript letters (a-d) indicate significant differences (p<0.05) between values in the same row by the Duncan’s multiple range test.

Download Excel Table

The oil content of C. rostrata, when extracted with acetone, was 8% (Table 1). The results showed that C. rostrata seed oil extracted with hexane, carbon tetrachloride, petroleum ether, acetone, and methanol yielded 7.5%, 7.5%, 8.0%, 9.0%, and 12.0% respectively. From the result, it was observed that more oil was extracted with methanol, followed by acetone and petroleum ether. The results obtained were higher than the percentage yield of 6.55%, 4.95%, 1.24%, 0.64%, and 0.21% of C. rostrata obtained by Odion et al. (2013) when extracted with petroleum ether, chloroform, ethyl acetate, and butanol respectively. This variation in % yield could be due to the polarity difference of the solvents used. From the results obtained (Table 1), it can be said that hexane and carbon tetrachloride are not very good solvents for Cola rostrata seed oil extraction due to low % yield, especially when compared with that reported for Allium satulum L oil (22.5%) and Lagenaria siceraria seed oil (39.22%) extracted using hexane (Garfar et al., 2012; Sani and Hassan, 2007).

The results of the oil content for D. edulis seeds are presented in Table 1. The percentage yield shows that extraction of oil using acetone, carbon tetrachloride, hexane, methanol, and petroleum ether yielded 20%, 9%, 22%, 11%, and 22% of oil respectively. Apart from the fact that D. edulis seed appears oily, hexane and petroleum ether gave a higher oil yield (22%) after the extraction process.

The result obtained for the oil content of D. tripetala seed (Table 1) shows that the highest yield obtained was by extraction with methanol (27.5%) followed by hexane (17%), acetone (16%) and petroleum ether (16%) the least oil yield was seen in the extraction with carbon tetrachloride (7.5%). The result shows that methanol is a better solvent for D. tripetala seed oil extraction. These results obtained are lower than those reported by Swaroopa et al. (2013) on the comparative extraction of castor seed oil using polar and non-polar solvents; from their result, using 20 g of seeds, hexane yielded 43.9%, petroleum ether 42%, and methanol yielded 46.9%. The result indicated methanol as a better solvent for both D. tripetala seed and carrot seed oils extraction. These variations could be a result of the polarity difference of the extracting solvents or the lipids content of the oil seeds.

The oil content of P. americana, as shown in Table 1, has the highest yield of 27.5% when extracted with hexane. The difference in the amount of oil extracted could be due to the polarity difference of the solvents or the fatty acids composition of the oil seeds. Extraction with methanol yielded 27.0%, while that of acetone gave 16.8% oil yield; the result also showed that a yield of 21% was obtained when extracted with petroleum ether, while the least yield of 12.0% was from the extraction with carbon tetrachloride. From the result obtained, the values are closely similar to that of the percentage oil yield of cottonseed oil (15.0-24.0%), soybeans (17.0-21.0%), safflower (25.0-40.0%), and mustard (24.0-40.0%) (Pritchard, 1991). This similarity could be due to the fatty acid composition of the oil seeds.

However, the oil contents of the seed oils in the present study are highly lower than the percentage yield of Moringa peregrina seed oil (49.80%) reported from Saudi Arabia (Tsaknis, 1998) but slightly lower than the commercial PKO used industrially with mean 28% yield as reported by Akubugwo and Ugborgu (2007). For solvent output results generally, hexane > petroleum ether > methanol > acetone > CCl4. Non-polar solvents tend to extract more oil, generally except in a few cases. There was a significant difference in the % yield of seed oils extracted with hexane and petroleum ether compared to others.

3.2. Acid value

The results of the acid value for C. rostrata seed oil extracted with acetone, carbon tetrachloride, hexane, methanol, and petroleum ether are presented in Table 2.

Table 2. Acid value of oils extracted using different solvents in mg KOH/g
Sample Hexane CCl4 Petroleum ether Acetone Methanol
Control1) 14.50±0.502)b3) 13.00±1.00a 14.00±0.50b 13.00±1.00a 13.50±0.50a
Cola rostrata 3.70±0.10b 3.70±0.20b 3.70±0.10b 3.10±0.10a 3.50±0.20b
Dacryodes edulis 3.40±0.10b 3.60±0.10c 2.60±0.10a 3.10±0.20b 3.80±0.20c
Dennettia tripetala 3.20±0.10b 2.70±0.10a 3.90±0.20c 3.80±0.20c 2.50±0.20a
Persea americana 2.60±0.10a 3.20±0.20b 2.80±0.10a 2.70±0.10a 2.40±0.20a

Commercial palm kernel oil (PKO).

Values are mean±SD (n=5).

Different superscript letters (a-c) indicate significant differences (p<0.05) between values in the same row by the Duncan’s multiple range test.

Download Excel Table

The results indicate that the acid value content of C. rostrata, D. edulis, D. tripetala, and P. americana seed oils was within 4 mg KOH/g acid value of oil suitable for edible purposes (Tan et al., 2002) as recommended by the Codex alimentarius for oil seeds (Abayeh et al., 1998), the values were lower than 14.0 mg KOH/g for palm kernel oil (PKO) by (Akubugwo and Ugborgu, 2007) similar to that used as control in this study, but greater than 0.50 mg KOH/g recommended for biodiesel (Arisa and Lazarus, 2008). The acid value gives an indication of the quality of fatty acids in oil (Gordon, 1993). The low acid values of the seeds indicate that the oil will be stable over a long period of time and is protected against rancidity and peroxidation, which may be a result of the presence of natural antioxidants in the seed, such as vitamin C and Vitamin A (Aremu et al., 2015). Acid value also indicates the edibility of an oil and its suitability for use in the paint and soap industries (Aremu et al., 2006).

However, a high acid value in oil indicates that the oil may not be edible but be useful for paint and soap production (Akintayo, 1997, Aremu et al., 2006), uses of acid value for biodiesel must be greater than the value of 0.50 mg KOH/g while appreciable acid value of oils is an indication of poisonous substance in the seed (Aremu et al., 2006). The acid value of the seed oils was in the order: C. rostrate > D. edulis > D. tripetala > P. Americana. For solvent output results, CCl4 > petroleum ether > hexane > acetone > methanol in decreasing order. This could be due to the polarity difference of the solvents or the fatty acids composition of the oil seeds. There was no significant difference in the acid values of the oils except for the CCl4, petroleum ether, and hexane extracts of some seed oils.

3.3. Iodine value

The results of the iodine value for C. rostrata, D. edulis, D. tripetala, and P. americana seed oils are shown in Table 3.

Table 3. Iodine value of oils extracted using different solvents in gl2/100 g
Sample Hexane CCl4 Petroleum ether Acetone Methanol
Control1) 18.10±0.502)b3) 16.10±1.00a 17.60±1.00b 16.20±0.50a 16.40±1.00a
Cola rostrata 33.25±0.15a 33.46±0.13a 33.97±0.13b 33.38±0.12a 33.63±1.02a
Dacryodes edulis 33.06±0.14a 34.10±0.15b 33.21±0.11a 33.35±0.15a 33.21±0.13a
Dennettia tripetala 33.06±0.12a 34.10±0.10b 33.76±0.14a 32.70±0.13a 33.50±0.10a
Persea americana 33.26±0.04a 34.00±0.15b 33.55±0.50a 33.00±0.13a 33.00±0.14a

Commercial palm kernel oil (PKO).

Values are mean±SD (n=5).

Different superscript letters (a,b) indicate significant differences (p<0.05) between values in the same row by the Duncan’s multiple range test.

Download Excel Table

According to Ugbogu et al. (2013), iodine value is a measure of the unsaturated levels in fats and oils. High iodine values (95.00±1.00) in J. Curcas oil is an indication of the presence of high unsaturated fatty acids such as oleic and linolelic acid (Emil et al., 2010), The values obtained in the results are lower than iodine value of melon seed of 124.5 gl2/100 g (Das et al., 2002). This could be due to the difference in the fatty acids composition of the oil seeds. High iodine values are usually above 190 gl2/100g, iodine values between 80 gl2/100 g-130 gl2/100 g indicate a semi-dry oil, while a non-drying oil has iodine value below 80 gl2/100 g (Fekarurhobo et al., 2009; Fernando and Akujobi, 1981). However, the results obtained for the four seed oils are higher than 16.00 gl2/100 g reported by Bwade et al. (2013) for pumpkin seed oil, 26.09 gl2/100 g reported by (Ogunsuyi and Daromola, 2013) for Almond seed oil and 20.30 reported by Belewu et al. (2010) for Jatropha curcas seed oil and even higher than 18.30 for the conventional PKO used industrially (Akubugwo and Ugborgu, 2007), and similar to that used as control in this study. These variations are possible because different oil seeds have different fatty acid content. For iodine value, the seed oils were in the order of D. tripetala > D. edulis > P. Americana > C. rostrata. For solvent output results, CCl4 > petroleum ether > methanol > hexane > acetone in decreasing order. However, the difference between methanol and hexane was not significant as far as iodine value is concerned. This slight variation in iodine value could be due to the polarity difference of the solvents or the fatty acids composition of the oil seeds. There was no significant difference in the iodine values of the seed oils, except carbon tetrachloride extracts of D. tripetala, D. edulis, and P. americana.

3.4. Saponification value

The results obtained for the saponification values of C. rostrata, D. edulis, D. tripetala, and P. americana are presented in Table 4. The result shows that the mean saponification values for C. rostrata were 193.0, 192.0, 197.44, 191.00, and 190.46 mg KOH/g when extracted using hexane, carbon tetrachloride, petroleum ether, acetone, and methanol respectively. The values obtained for C. rostrata were higher than 140.3 mg KOH/g for Tallow oil (Warra et al., 2010) and 179.52 and 185.00 mg KOH/g for Cypenus esculentum oil extracted using hexane reported by (Akpe and Inezi, 2018) and (Hassan et al., 2007), respectively. D. edulis seed oil showed mean saponification values of 190.74, 196.74, 192.00, 192.14, and 198.31 mg KOH/g when extracted using hexane, carbon tetrachloride, petroleum ether, acetone, and methanol, respectively. The values obtained for D. edulis seed oil are lower than 246.60 mg KOH/g, as reported by Akubugwo and Ugbogu (2007), and 249.90 mg KOH/g for PKO was used as a control in this study. The values obtained are comparable to soybean seed oil (192.30 mg KOH/g) reported by Akanni et al. (2005) and 195.0 mg KOH/g for groundnut seed oil (Ayoola and Adeyeye, 2010).

Table 4. Saponification value of oils extracted using different solvents in mg KOH/g
Sample Hexane CCl4 Petroleum ether Acetone Methanol
Control1) 245.50±1.002)a3) 241.60±1.00b 245.40±0.60b 241.40±0.50a 242.10±0.50a
Cola rostrata 193.00±1.04b 192.00±1.08b 197.44±1.06c 191.00±0.55a 190.46±1.04a
Dacryodes edulis 190.74±0.36a 196.74±1.00c 192.00±1.05b 192.14±1.02b 198.31±1.04c
Dennettia tripetala 202.52±1.03c 201.96±1.16c 194.11±0.50a 198.32±1.03b 196.35±1.05b
Persea americana 189.34±1.06b 182.23±1.12a 199.44±1.10c 198.32±1.02c 196.71±1.03c

Commercial palm kernel oil (PKO).

Values are mean±SD (n=5).

Different superscript letters (a-c) indicate significant differences (p<0.05) between values in the same row by the Duncan’s multiple range test.

Download Excel Table

The mean saponification values for D. tripetala oil extracted using hexane, carbon tetrachloride, petroleum ether, acetone, and methanol shown in Table 4 were 202.52, 201.96, 194.11, 198.32, and 196.35 mg KOH/g respectively. The results obtained are comparable to that of African bush mango (202.90 mg KOH/g) reported by Igwenyi (2014) and 194.80 mg KOH/g (Melon seed oil) reported by Egbebi (2014).

The mean SVs for P. americana seed oil extracted using acetone, carbon tetrachloride, hexane, methanol, and petroleum ether as shown in Table 4, were 189.34, 182.23, 199.44, 198.32, and 196.71 mg KOH/g respectively. Also, from the result (Table 4), it is observed that the highest saponification values were obtained from D. tripetala (201.96 mg KOH/g and 202.52 mg KOH/g) when extracted with carbon tetrachloride and hexane respectively while the least saponification values of 182.23 and 190.46 mg KOH/g were obtained for carbon tetrachloride extraction of P. americana and C. rostrata respectively. The saponification value of the seed oils was in the order: D. tripetala > P. Americana > D. edulis > C. rostrata. For solvent output results generally, hexane > CCl4 > petroleum ether > methanol > acetone in decreasing order. This trend may be due to the lipids content of the oil seeds or the polarity difference of the extracting solvents. Seed oils for soap making may be extracted using hexane, CCl4, and petroleum ether because of the high saponification value of their oil extracts. There was a significant difference in saponification values of seed oils extracted with hexane, CCl4, and petroleum ether. This may be due to the natural fatty acid composition of the oil seeds or the polarity difference of the extracting solvents.

3.5. pH

The mean pH values of the different seed oils are shown in Table 5. The result shows that D. edulis seed oil has a pH of 4.4-6.1. Oils extracted with methanol gave the lowest value of 4.4, with carbon tetrachloride giving a pH of 4.6, acetone gave 5.2, while petroleum ether and hexane gave 6.0 and 6.1, respectively.

Table 5. Conductivity (μS/cm) and pH of oils extract using different solvents
Sample Property Hexane CCl4 Petroleum ether Acetone Methanol
Control1) Cond. 0.30±0.012)a3) 0.27±0.02a 0.31±0.02b 0.28±0.01a 0.29±0.01a
pH 5.10±0.10b 4.80±0.10a 5.00±0.20b 4.90±0.10a 4.70±0.20a
Cola rostrata Cond. 0.32±0.01a 0.31±0.02a 0.31±0.02a 0.32±0.01a 0.32±0.03a
pH 6.10±0.10a 6.40±0.10a 6.20±0.10a 6.20±0.10a 6.10±0.20a
Dacryodes edulis Cond. 0.30±0.03a 0.31±0.01a 0.30±0.02a 0.33±0.02a 0.32±0.02a
pH 6.10±0.20c 4.60±0.10a 6.30±0.10c 5.20±0.10b 4.40±0.20a
Dennettia tripetala Cond. 0.33±0.01a 0.30±0.02a 0.30±0.01a 0.32±0.02a 0.32±0.02a
pH 6.20±0.10a 6.20±0.10a 6.30±0.20a 6.40±0.10a 6.30±0.20a
Persea americana Cond. 0.31±0.02a 0.31±0.02a 0.32±0.03a 0.32±0.03a 0.32±0.03a
pH 6.20±0.10a 6.30±0.10a 6.10±0.10a 6.10±0.20a 6.20±0.20a

Commercial palm kernel oil (PKO).

Values are mean±SD (n=5).

Different superscript letters (a-c) indicate significant differences (p<0.05) between values in the same row by the Duncan’s multiple range test.

Download Excel Table

C. rostrata seed oil extract shows slight acidity from the pH values (Table 5). The pH of 6.1, 6.4, 6.1, 6.3, and 6.2 was recorded for C. rosrtata seed oils extracted with methanol, carbon tetrachloride, hexane, acetone, and petroleum ether, respectively.

D. tripetala seed oil extract shows pH of 6.3, 6.2, 6.2, 6.4, and 6.3 using methanol, carbon tetrachloride, hexane, acetone, and petroleum ether, respectively.

The pH range for P. americana seed oil was 6.1-6.3. The result shows pH of 6.2, 6.3, 6.2, 6.3, and 6.1 for P. americana seed oils extracted with methanol, carbon tetrachloride, hexane, acetone, and petroleum ether, respectively. The slight and insignificant variation in pH may be due to the polarity difference of the solvents or the nature of the fatty acids in the oil seeds.

Since pH indicates the level of acidity and alkalinity, it ranges from 1 to 14 and pH less than 7 is considered to be acidic, while pH more than 7 is said to be alkaline, pH at point 7 is neutral. The results showed that the seed oils were slightly acidic since the pH values were mostly between 6.0-6.4, except for D. edulis, which is a little more acidic with a pH range of 4.4-4.6. These values were slightly higher than PKO used as a control in this study, as its values ranged between 4.7-5.1 across the solvents. The slight acidity of most oils is an indication that they can be edible, as they naturally contain fatty acids. Highly acidic oils are not edible except after alkaline refining. The pH values obtained are higher than 3.6 (Leganeria breviflora) and 5.70 (Colocynthis citrullus) seed oils reported by Taiwo et al. (2016). The result is in the close range and slightly higher than 5.30 (Brachystegia eurycoma), 5.65 (Cucurbita pepo), 5.59 (Luffa cylindrical), and 6.07 (Cucumis melo) reported by (Ibeto et al., 2012). All the seed oils had no significant difference in their pH across the solvents except D. edulis.

3.6. Electrical conductivity

The electrical conductivity of the different seed oil extracts is also shown in Table 5. The result shows the seed oil conductivities to be between 0.30-0.33 μS/cm across the solvents. The mean range of values were 0.31-0.32, 0.30-0.33, 0.30-0.33, and 0.31-0.32 μS/cm for C. rostrata,D. edulis,D. tripetala, and P. americana, respectively, across the solvents. These values were slightly higher than PKO used as a control in this study, as its values ranged between 0.27-0.31 across the solvents. There was no significant difference in the electrical conductivity of the seed oils across the solvents. Conductivity is used to determine whether a substance is an electrical conductor or an insulator. Electrical conductivity is also an indication that the oil contains mobile ions or free radicals. The presence of radicals in oils can make them prone to decomposition of fatty acids, leading to fast deterioration. The mean conductivity values of the seed oils were generally low, and there is no available data for comparison at the moment. The low values of the seed oils indicate that they are poor conductors. For other physical properties, the oils were generally bright in color and attractive, non-offensive in odor, and liquid at room temperature.

4. Conclusions

The results of this study revealed that D. edulis and P. americana seeds were better oil sources than D. tripetala and C. rostrata based on percentage yield. The acid values of the four seed oils suggest that they are edible oils irrespective of the extracting solvent; the iodine value classifies the seed oils as non-drying oils (suitable for paint making, especially with dehydration), and the SV reveals that the oils are good for soap making. The four seed oils compete favorably with PKO used industrially in some properties, especially IV. Vegetable oil properties are affected by extracting solvents to an extent, though not significant in some cases. For high percentage yield, hexane and petroleum ether were preferable solvents, while hexane, petroleum ether, and CCl4 are preferable to methanol and acetone as extracting solvents for high AVs, IVs, and SVs. It was suggested that hexane, petroleum ether, and CCl4 were suitable extracting solvents for industrial purposes, while D. edulis, D. tripetala, and P. Americana oils are economically viable due to their high % yield, SVs, and IVs.

Acknowledgements

None.

Conflict of interests

The authors declare no potential conflicts of interest.

Author contributions

Conceptualization: Essien QE, Akpe MA. Methodology: Essien QE, Udo OO. Formal analysis: Akpe MA, Nwobodo CI. Validation: Udo OO. Writing - original draft: Essien, QE. Writing - review & editing: Akpe MA, Nwobodo CI.

Ethics approval

This article does not require IRB/IACUC approval because there are no human and animal participants.

Funding

None.

ORCID

Qeency Etim Essien (First author) https://orcid.org/0009-0008-9046-658X

Michael Akomaye Akpe (Corresponding author) https://orcid.org/0000-0001-7258-7427

Ofonime Okon Udo https://orcid.org/0009-0005-9685-1671

Collins Irechukwu Nwobodo https://orcid.org/0009-0000-0418-719X

References

1.

Abayeh OJ, Alna EA, Okoungha CO. Oil content and oil quality characteristics of some Nigerian oils seed. J Pure Applied Sci. 1:17-33 1998;

2.

Abubakar ANF, Achmadi SS, Suparto IH. Triterpenoid of avocado (Persea americana) seed and its cytotoxic activity toward breast MCF-7 and liver HEPG2 cancer cells. Asian Pac J Trop Biomed. 7:397-400 2017;

3.

Ajiwe VIE, Okeke AC, Nnabuike B, Ogunleye GA, Elebo E. Applications of oils extracted from African star apple (Chrysophylum africanum) horse eye bean (Mucana sloanei) and African pear (Dacryodes edulis) seeds. Bio Resour Technol. 59:259-261 1997;

4.

Akanni MS, Adekunle AS, Oluyeme EA. Physicochemical properties of some non-conventional oil seeds. J Food Technol. 3:177-181 2005;

5.

Akintayo ET. Chemical composition and physicochemical properties of fluted pumpkin (Telfairia occidentalis) seed and seed oils. Riv Ital Sostanze Grasse. 74:13-15 1997;

6.

Akpe MA, Inezi FP. Physicochemical properties of Alchorea cordiforlia, Cyperus esculetum and Irvingia gabonensis seed oil and their applications. Asian J Appl Chem Res. 1:1-7 2018;

7.

Akubugwo IE, Ugbogu AE. Physicochemical studies on oils from five selected Nigerian plant seeds. Pak J Nutr. 6:75-78 2007;

8.

Aluyor EO, Ori-Jesu M. The use of antioxidants in vegetable oils, a review. Afr J Biotechnol. 7:4836-4842 2008;

9.

AOAC Official Methods of Analysis.16thed Association of Official Analytical Chemists. Gaithersburg, MD, USA. 1998

10.

AOAC Official Methods of Analysis.17thed Association of Official Analytical Chemists. Gaithersburg, MD, USA. 2002

11.

AOCS Official Methods and Recommended Practices of the American Oil Chemists’ Society.AOCS Press. Washington DC, USA: 1993

12.

Aremu MO, Ibrahim H, Bamdele TO. Physicochemical characteristics of the oils extracted from some Nigerian plant foods. Int J Chem Process Engr Res. 32:36-52 2015;

13.

Aremu MO, Olafe O, Akintayo ET. Chemical composition and physicochemical characteristics of two varieties of bambara groundnut (Vigna subterrenea) flours. J Appl Sci. 6:1900-1903 2006;

14.

Arisa NU, Lazarus A. Production and refining of Dacryodes edulis “native pear” seeds oil. Afr J Biotechnol. 7:1344-1346 2008;

15.

Ayoola PB, Adeyeye A. Effect of heating and on the chemical composition and physicochemical properties of Arachis hypogea (groundnut) seed flour and oil. Pak J Nutr. 9:751-754 2010;

16.

Belewu MA, Adekola FA, Adebayo GB, Ameen OM, Muhammed NO, Olaniyan AM, Adekola OF, Musa AK. Physiochemical characteristics of oil and biodissel from Nigerian and Indian Jatropha curcas seeds. Int J Biol Chem Sci. 4:524-529 2010;

17.

Bwade KE, Aliyu B, Kwaji AM. Physiochemical properties of pumpkin seed oil relevant to biodiesel production and other industrial applications. Int J Engr Bus Enterpr Appl. 4:72-78 2013;

18.

Das M, Das SK, Suthar SH. Composition of seed and characteristics of oil from Karingda. Int J Food Sci Technol. 37:893-896 2002;

19.

Efeovbokhan VE, Hymore FK, Raji D, Sanni SE. Alternative solvents for Moringa oleigera seeds extraction. J Appl Sci. 15:1073-1082 2015;

20.

Egbebi AO. Comparative studies on the three different species of melon seed (Citrulus vulgaries, Cucumcropsis manni and Lagenaria siceraria). Sky J Food Sci. 3:1-4 2014;

21.

Eka OU. Studies on nutrient composition of the fruit of African pear. West Afr J Bio Appl Chem. 2:3-7 1997;

22.

Emil A, Yaakob Z, Kumar MNS, Jahim JM, Salimon J. Comparative evaluation of physicochemical properties of Jatropha seed oil from Malaysia, Indonesia and Thailand. J Am Oil Chem Soc. 87:689-695 2010;

23.

Fekarurhobo GK, Obomanu FG, Maduelosi JN. Effects of short-term exposure to sunlight on the quality of some edible vegetable oils. Res J Appl Sci. 17:152-156 2009;

24.

Fernando CEC, Akujobi EO. Chemical analysis selected vegetable oils and fats of Sokoto State of Nigeria. J Basic Appl Sci. 1:11-14 1987;

25.

Garfar MK, Itodo AU, Warra AA, Abdullahi I. Extraction and physicochemical determination of garlic (Allium sativum L.) oil. Int J Food Nut Sci. 1:4-7 2012;

26.

Gordon M. Fats and fatty foods. In: Food Industries Manual. 23rded In: Kill RC, editor.EditorBlackie Academic and Professional. London, UK: p p. 179-186 1993;

27.

Hassan LG, Osoba O, Umar KJ, Inwa M. Physicochemical analysis of Cyperus escubentus oil. Yauri J Arts Sci. 2:1-4 2007;

28.

Hassan LG, Sani NA. Comparative studies on the physicochemical properties of bottle gourd Lagernaria suceraria seeds oils extracted by two methods. Nigeria J Basic Appl Sci. 15:50-51 2007;

29.

Ibeto CN, Okoye COB, Ofoefule AU. Comparative study of the physicochemical characterization of some oils as potential feedstock for biodiesel production. Int Scholarly Res Not. 2012:62518 2012;

30.

Idu MD, Erhabor JO, Efijuemue HM. Documentation on medicinal plant sold in markets in Abeokuta, Nigeria. Trop J Pharm Res. 9:110-118 2010;

31.

Kadji BRL, Kone FMT, Sika AE, Dabonne S. Physico-chemical properties of safou (Dacryodes edulis) fruits grown in cote d’Ivoire. J Appl Biosci. 105:10103-10110 2016;

32.

Kaseke T, Opara UL, Fawole OA. Fatty acid composition, bioactive phytochemicals, antioxidant properties and oxidative stability of edible fruit seed oil: Effect of preharvest and processing factors. Heliyon. 6:E04962 2020;

33.

Luque-Garcia JL, Luque de castro MD. Ultrasound assisted Soxhlet extractetion: An expeditive approach for solid sample treatment, application to the extraction of total fat from Oleaginous seeds. J Chromatogr A. 1034:237-242 2004;

34.

Obasi NBB, Okolie NP. Nutritional constituents of the seeds of the African pear (Dacryodes edulis). J Food Chem. 46:297-299 1993;

35.

Odion EE, Poh CF, Falodun A, Adelusi SA. Cola rostrata: Phytochemical and toxicity studies. J Appl Sci Environ Manage. 17:603-607 2013;

36.

Ogunsuyi HO, Daramola BM. Evaluation of almond (Prunus amydalus) seed oil as a viable feedstock for biodiesel fuel. Int J Biotechnol Res. 1:120-127 2013;

37.

Okene EO, Evbuomwam BO. Solvent extraction and characterization of oil from coconut seed using alternative solvents. Intern J Engr Tech Res. 2:135-138 2014;

38.

Okwu DE. Evaluation of the chemical composition of indigenous spices and flavouring agents. Global J Pure Appl Sci. 7:455-459 2001;

39.

Okwu DE, Morah FNI. Mineral and nutritive value of Dennettia tripetala fruits. J Fruits. 59:437-442 2004;

40.

Onyeike EN, Acheru GN. Chemical composition of selected Nigerian oil seeds and physicochemical properties of the oil extracts. J Food Chem. 77:431-437 2002;

41.

Oyemitan IA, Iwalew EO, Akanmu MA, Olugbade TA. Antinociceptive and antiinflammatory effects of essential oil of Dennethia tripetala Gbaker (Annonaceae) in rodents. Afr J Trad COM. 5:355-362 2008;

42.

Roy S, Sarkar T, Chakraborty R. Vegetable seeds: A new perspective in future food development. J Food Process Preserv. 46:e17118 2022;

43.

Roy S, Sarkar T, Upadhye VJ, Chakraborty R. Comprehensive review on fruit seeds: Nutritional, phytochemical, nanotechnology, toxicity, food biochemistry, and biotechnology perspective. Appl Biochem Biotech. 196:4472-4643 2024;

44.

Sani NA, Hassan LG. Preparation and analysis of the physical and chemical properties of soap from Lageneria siceraria seeds oil. Namoda Tech Scope J. 7:23-32 2007;

45.

Shirana P, Khushbu P, Faldu N, Thakkar V, Shubramanian RB. Extraction and analysis of Jatropha curcas L. seed oil. Afr J Biotechnol. 10:18210-18213 2011;

46.

Swaroopo R, Dasiri A, Vaibhav VG. Comparative extraction of castor oil using polar and won polar solvents, department of chemical engineering India. Int J Current Engr Technol. 78:39 2013;

47.

Taiwo AA, Osifeso O, Adepoju MA, Olawunmi OM. Comparative studies on the chemical composition and anti-nutritional contents of the Lagenaria breviflora and Colocynthis seeds. Sky J Food Sci. 5:045-049 2016;

48.

Tsaknis J. Characterization of Moringa peregrine Arabia seed oil. Grasas Aceites. 49:170-176 1998;

49.

Ugbogu AE, Akubugwo EI, Ukegbu FO, Chinyere CG, Ugbogu OC, Oduse KA. Nutritional and chemical composition of Jatropha curcas seed oil from Nigeria. Int J Biosci. 3:15-25 2013;

50.

Umoh IB. Nutritional Quality of Plant Foods. Post-Harvest Research Unit. University of Benin. Benin City, Nigeria: 1998

51.

Vermaak I, Kamatou GPP, Komane-Mofokeng B, Viljoen AM, Beckett K. African seed oils of commercial importance cosmetic applications. S Afr J Bot. 77:920-933 2011;

52.

Warra AA, Hassan LG, Gunu SY, Jega SA. Cold-process synthesis and properties of soaps prepared from different triacyglycerol sources. Nigerian J Basic Appl Sci. 18:315-321 2010;